Seven wires under one name
The name 1x7 describes a seven-wire arrangement, and that arrangement is the first thing to picture when reading the series table. One wire forms the centre, and six wires wind around it, so the strand behaves as a single unit even though it is made from several wires. A buyer who pictures that arrangement will read diameter and grade figures as figures for the whole strand, not for a single wire inside it, and that reading matches the way the MIC product page table presents them.
The arrangement also explains why the series name matters in an inquiry. Naming the 1x7 series tells the reader exactly which arrangement is under discussion, while naming strand in general leaves the arrangement open. An inquiry that names the series, the diameter, and the grade from the table gives the company a complete starting point, while an inquiry that names strand alone usually receives a reply that asks which series was meant.
The series table, read at face value
The MIC product page table for the 1x7 series lists nominal diameters of 9.5, 11.10, 12.70, 15.20, 15.70, and 17.80 millimetres, with tensile strength grades of 1860 and 1960 newtons per square millimetre, and a relaxation figure of not more than 2.5 percent over 1000 hours. Those figures are quoted at series level, with the MIC product page named as their source, and they are the only strand figures published on the listing. No diameter, grade, or relaxation figure beyond that table appears anywhere else in the steel line.
Reading the table at face value means accepting both its usefulness and its limits. The table lets a buyer compare diameters and grades within the series, and lets a buyer name a diameter and a grade in an inquiry with confidence that the names match the listing. The table does not, by itself, settle which diameter or grade suits a particular structure, and it does not replace a project specification. A buyer who treats the table as a shortlist rather than as a recommendation will use it correctly.
Names beside the series table
Beside the 1x7 series, the steel listing names several further items without tables: 1x2 and 1x3 PC strand, compacted steel strand, prestressed concrete wire, anchorage, cable bolt strand, and precision rolled threaded steel, known as rock bolt bar. Each of those names appears on the steel index or on its own listing page at name level only, because the source pages list them without detail. A buyer who recognises one of those names can mention it in an inquiry, and the company can confirm what sits behind the name.
Keeping those names at name level follows the sources, and the practical effect is simple: no dimension, grade, or performance figure is attached to a name that the sources never measured. A buyer who needs detail on a listed name should ask for it directly, naming the item and the application, rather than assuming that a name on an index carries the same table as the 1x7 series. The reply will then supply whatever detail the company holds for that item.
Application areas, listed without added wording
The MIC listing names the following application areas for the steel line: bridges, railways, highways, subways, tunnels, airports, nuclear power plants, real estate construction, geotechnical engineering, industrial buildings, and precision manufacturing. The official site homepage names three broader areas: energy, mining, and building. This guide lists those areas exactly as named, and adds no performance wording for any of them, because the application pages behind those names were never opened into full detail.
A listed area is still useful in an inquiry, because it tells the company which kind of project the strand is intended for. A bridge inquiry, a tunnel inquiry, and a geotechnical inquiry will each receive different follow-up questions, even when they name the same series and diameter, because the surrounding requirements differ. Naming the area early therefore saves a round of questions, even though the area name alone settles nothing about suitability.
Telling strand, wire, and anchorage apart in writing
Prestressed steel strand, prestressed concrete wire, and anchorage are three different steel-line items, and confusing them in writing is the most common cause of a slow first exchange. Strand is the seven-wire product described above, wire is a separate listed item with its own page, and anchorage covers the parts that hold a tensioned element in place. An inquiry that names the wrong one of the three will receive a reply about the wrong product, however clearly the rest of the message is written.
The remedy is a habit rather than a glossary: write the product name exactly as it appears on the listing, and read it back before sending. Where two names look alike, add the series or the application area beside the name, so the reader can see which item was meant even if one word is misread. That small check costs seconds, and it prevents the most frequent misunderstanding in strand correspondence.
Turning basics into a first inquiry
A first inquiry built on this guide has four parts: the series name, the diameter and grade listed in the table, the application area, and the standard name if the project requires one. Each part answers a question the company would otherwise have to ask, and together they let the reply focus on the points that depend on the specific order. A buyer who writes those four parts in the opening message will usually receive a reply that addresses the order itself, rather than a reply that asks for the basics.
The commercial points belong in the same first message. Ask in the inquiry about the minimum order quantity, the lead time, and the payment terms before placing an order, and name any document, sample, packaging requirement, or shipping method that matters to the order. Those points are not stated as figures anywhere in the listing, because the source pages publish no fixed commercial terms, so the inquiry is the place where they become agreed terms for the actual order.
What basics do not settle
Basics do not settle suitability, and a buyer should not expect them to. The series table gives diameters and grades, the index gives names, and the application list gives areas, but none of those decides whether a particular diameter and grade suit a particular structure. That decision belongs to the project specification and to the reply, where the company can respond to the structure, the area, and the standard together. A guide that pretended otherwise would be inventing the very detail that the listing leaves open.
Basics also do not settle documents. A standard name on a listing page is a name, not a document held for an order, and a buyer who needs a document should name it in the inquiry and ask for the document itself. The certificates page explains that position in full, and the same habit applies here: name the document, the product, and the destination market, and ask for the paper rather than for a general assurance.
A second look before sending
Before sending a strand inquiry, read it once against this guide: does it name the series, a diameter and a grade from the table, an application area, and a standard if one applies, and does it ask the commercial questions in the same message. A message that passes that check is ready to send, and a message that fails it is easy to repair, because each missing part has an obvious place in the opening paragraph.
After the reply arrives, read it the same way, comparing the product, the diameter, the grade, and the standard in the reply with the ones in the inquiry. Where the reply names a different item or a different grade, ask about the difference before proceeding, because a near match in strand names is not a match. That second look turns a reply into a record, and a record into an order that both sides understand in the same way.